Magicmotorsport FLEX Slave – ECU programming tool for OBD, bench, BDM, boot and JTAG with Master support
1.279,91 € - 2.983,01 €
- Read, write and update engine and gearbox ECUs via OBD
- FlexBox for bench, BDM, bootloader, JTAG and AUD included
- Clone ECUs, more than 25,000 vehicles according to Magicmotorsport
- Slave version with Master support from The Optimizer
- Complete cable and adapter set in the FLEX case
- Description
- Jetzt kontaktieren
- Additional information
- Reviews (0)
Description
Magicmotorsport FLEX Slave – ECU programming tool for OBD, bench, BDM, boot and JTAG with Master support
A software update after an ECU replacement, cloning a faulty gearbox control unit or a remap for a customer: with the Magicmotorsport FLEX you read and write most engine and gearbox ECUs directly via the OBD port. For everything OBD can’t do, the included FlexBox module programmes ECUs in bench, BDM, bootloader, JTAG and AUD mode. This Slave version comes with Master support from The Optimizer.
A good fit if you …
- run a workshop that reads, writes, clones or updates ECUs
- want to work both via OBD and on removed ECUs
- prefer to leave file editing to an experienced Master tuner
- work on vehicles from many different manufacturers
Probably not for you if you …
- want to edit the read files yourself – that requires a Master version
- only read fault codes and do service resets – a diagnostic tool is enough for that
What the FLEX can do
- OBDRead, write and update the software of most engine ECUs directly via the OBD port
- FlexBoxProgramme ECUs in bench, BDM, bootloader, JTAG and AUD mode
- CloningDuplicate engine and gearbox control units, for example after a failure
- Error detectionConnection and communication errors are detected while reading and writing
- Vehicle coverageMore than 25,000 vehicles according to Magicmotorsport
- OnlineSoftware, protocols and updates via your internet connection
Slave with Master support from The Optimizer
A Slave tool reads and writes ECUs just like a Master. However, the read files are encrypted and edited by the assigned Master tuner – for this tool, that’s The Optimizer. You send the original file, receive the edited file back and write it to the ECU with the FLEX.
Updates and new protocols run on an annual subscription. To renew: Magicmotorsport FLEX subscription.
Vehicle lists and guides
What’s in the box
| FLX1.1 | FLEX base module |
|---|---|
| FLX1.9 | FlexBox module |
| FLX2.10 | OBD cable FLEX to CAN/K-Line (red) |
| FLX2.11 | OBD cable FLEX to ENET (green) |
| FLX3.3 | Cable FlexBox port C to NEC 7F00 XX |
| FLX3.4 | Cable FlexBox port D to BDM MPC5xx |
| FLX3.9 | USB 2.0 cable AM-BM, 1.8 m |
| FLX4.1 | FlexBox port E 40-pin adapter for FLK35 |
| FLX9.1 | FLEX and FlexBox diagnostic adapter |
| FLK35 | Cabling kit with colour-coded FLX3.5 wiring harness |
| FLK42 | Adapter kit with 6 pin adapters for FLX35 |
| FLK49 | Switch-mode power supply with plugs |
| FLX8.10 | FLEX case |
Good to know
Modifying engine or gearbox software can affect the vehicle’s type approval, warranty and insurance cover. For road use, it is only permitted with the appropriate registration or approval.
Always back up the original file before writing and connect the vehicle to a battery charger or power supply. According to Magicmotorsport, the FLEX comes with a limited lifetime warranty, and technical support is included.
Is your ECU supported?
Tell us the vehicle, engine and ECU – we’ll check support before you buy.
Questions we often get
What’s the difference between Slave and Master?
Both read and write ECUs. With a Master you edit the files yourself. With a Slave, the files are encrypted and edited by the Master tuner – for this tool, The Optimizer.
Do I need a subscription?
For new protocols and updates, the FLEX runs on an annual subscription that you can renew.
Can I also work on removed ECUs?
Yes, with the included FlexBox module in bench, BDM, bootloader, JTAG and AUD mode.
Can I clone ECUs?
Yes, many engine and gearbox control units can be duplicated. Magicmotorsport’s list of clonable ECUs shows exactly which ones.
Additional information
| Weight | 2 kg |
|---|
Be the first to review “Magicmotorsport FLEX Slave – ECU programming tool for OBD, bench, BDM, boot and JTAG with Master support”
You must be logged in to post a review.
Reviews
There are no reviews yet.